Features:

• 26cc, 1.3 Hp Two-Stroke Engine features two piston rings and a stress relieved, chrome plated cylinder for longer engine life
• Powered Reversing feature allows you to instantly reverse drilling direction with a push of a lever
• Portable and light weight drill anywhere and in any position without the hassles of electrical cords, compressors or generators
• 1/2" Chuck Capacity accepts a wide variety of wood, steel, and concrete bits
• Dual Position Front Handle allows the handle to be mounted on either side of the unit for added versatility
• 1 / 2 / 5 Warranty Coverage provides One-Year coverage for professionals, Two-Year coverage for homeowners, and Five Years on the Electronic Ignition Module

Specifications:

• Engine Displacement cc (cu. in.): 26 (1.6)
• Power (h.p.): 1.3 @ 8500 RPM
• Carburetion: Walbro Diaphragm
• Ignition System: Transistorized Electronic
• Fuel Tank Capacity / fl. oz. (cc.): 17.0 (500)
• Front Handle: 2 Position / Adjustable
• Clutch System: Centrifugal
• Reduction Ratio: 20:1
• Chuck Speed: 0 - 450 RPM
• Chuck Capacity: 1/2"
• Drill Bit Capacity: 1" Wood, 1/2" Steel, 1/2" Concrete
• Dry Weight: 11.0 lbs.

Features:

• 26cc, 1.3 Hp Two-Stroke Engine features two piston rings and a stress relieved, chrome plated cylinder for longer engine life
• Unique Locking Mechanism allows you to manually back out a bit during use
• Portable and light weight drill anywhere and in any position without the hassles of electrical cords, compressors or generators
• 1/2" Chuck Capacity accepts a wide variety of wood, steel, and concrete bits
• Dual Position Front Handle allows the handle to be mounted on either side of the unit for added versatility
• 1 / 2 / 5 warranty coverage provides One-Year coverage for professionals, Two-Year coverage for homeowners, and Five Years on the Electronic Ignition Module

Specifications:

• Engine Displacement cc (cu.in.): 26 (1.6)
• Power (h.p.): 1.3 @ 8500 RPM
• Carburetion: Walbro Diaphragm
• Ignition System: Transistorized Electronic
• Fuel Tank Capacity / fl. oz. (cc.): 17.0 (500)
• Front Handle: 2 Position / Adjustable
• Clutch System: Centrifugal
• Reduction Ratio: 20:1
• Chuck Speed: 0 - 450 RPM
• Chuck Capacity: 1/2"
• Drill Bit Capacity: 1" Wood, 1/2" Steel, 1/2" Concrete
• Dry Weight: 9.9 lbs.

Features:

• Automatic chain oiling
• Side access chain tensioner
• Engine Displacement for all three models: 25.4 cc (1.55 cu. in.)

DANGER! Risk of Electrocution: Pole pruners are not insulated. Approaching or contacting electric power lines with these tools may cause serious injury or death from electrocution.

017 Specifications:

• 30.8cc
• 1.9hp

026 Specifications:

• 48.7cc
• 3.5hp
• Parts Available

When you think of concrete, metal, asphalt, masonry, stone and ductile iron, you think tough. And when these are the kinds of materials you're dealing with, you'd better think about a Stihl Cutquik cut-off machine. Construction sites, demolition work or rescue operations - whenever the going gets rough - Stihl Cutquik cut-off machines provide all the power and portability needed for fast, easy cutting.

Specifications:

• Weight: 21.6 lbs.
• Displacement: 3.9 cu. in.
• Engine Power: 4.4 bhp
• Fuel Capacity: 25 oz.
• Engine Speed: 9,700 rpm
• Arbor Size: 20 mm
• Wheel Size: 14"

1/2" Magnum®

• 1/2" Trigger Speed Control Reversing
• 7 Amp MILWAUKEE Motors
• Helical Cut, Heat Treated Gears
• Durable, Glass Reinforced Nylon Handles
• All Models Variable Speed, Control Reversing Except 1101-1 and 3102-6
• All Ball And Roller Bearings

Specifications:

• Capacity in Steel: 1/2"
• Volts AC Only: 120
• AMPS: 7.0 except 3300-1: 5.5

Standard Equipment:

• For 1001-1, 1007-1, 1101-1, 1107-6, 1250-1 Include: Side Handle, Chuck Key and Rubber Flex Key Holder

For 3102-6, 3002-1, 3107-6, 3300-1 Include: 48-06-2871 Right Angle Drive, 49-96-4060 9/16" Open End Wrench, 49-96-0080 3/16" Socket Wrench, Chuck Remover Bar, Side Handle and Impact Resistant Carrying Case 48-55-0802 (Steel Case for 3300-1 is 48-55-0200)

Kits 3300-1 and 3107-6 Also Contain: 8' 3-Wire Quik Lok Cord Set 48-76-4008

• Large 4-3/4" x 4-3/4" Capacity
• All Models Use Standard 44-7/8" x 1/2" x .020" Band Saw Blades
• Powerful Motor With Long Life Brushes And High Output Fans - Provides high performance for the toughest cutting operations
• Optimum Speed Range - Cuts pipes, bolts, re-bar, angle iron, tracks and other profiles in a variety of materials; all models include Super-Tough® Bi-Metal blades
• All Ball And Roller Bearing Construction For Smooth, Durable Operation

High Torque Worm Gear And Chain Drive Mechanism - For optimum motor torque transfer and durability; self-lubricated for maximum wear resistance

• Excellent Balance - Center of gravity located directly over blade results in straighter cuts while reducing operator fatigue; front T-handle provides superior control
• Open Line Of Sight For More Accurate Cut
• Blade Tightening Lever - Long life cam provides quick and easy blade changes

Standard Equipment:

• For 6230 and 6236 - One 14-Tooth Super-Tough® Bi-Metal 48-39-0510. For 6232-6 and 6238 - One 14-Tooth Super-Tough® Bi-Metal Blade 48-39-0510 and Impact Resistant Carrying Case 48-55-6200.

Features:

• A proven performer with positive slug ejection
• Twist drill and tapping options

Specifications:

• Height - 16-1/4"
• Width - 7-1/2"
• Length - 9-3/8"
• Weight - 28 lbs.
• Motor - 0.9 HP 700W (single phase) 120V / 6.0A 450 RPM (no load)
• Arbor Bore - 3/4"
• Drill Point Breakaway - 650 lbs. on 1" plate
• Magnet Base Dimensions - 3" x 6-1/4"
• Magnet Dead Lift - 1480 lbs. on 1" plate
• Slugger cutter diameter (maximum) - 1-3/8"
• Slugger depth of cut (maximum) - 2"

MAGFORCE

Tapmatic® Edge crème lubricates Slugger cutters when drilling in horizontal and inverted positions. The heat that is generated while drilling liquifies the cutting paste, providing coolant and extending cutter life.

Tru-Blu coolant, used with Slugger cutters, is a water-based fluid designed to extend tool life, improve surface finish and reduce heat build-up when drilling.

• Super Spool™ for Open- and Closed-Center operation
• Internal control prevents overspeeding, allows flows up to 12 gpm (45 lpm)
• Reversible operation
• High torque for drilling salt-cured and creosoted poles
• Heat-insulated handle, ergonomically positioned for comfort
• Twin hammer impact mechanism for high performance and reliability
• Well-balanced for comfortable operation

Specifications:

• Capacity: 7/16 in. quick change chuck or 1/2 in. square drive
• System: Super Spool™ selector control for use on Open- and Closed-Center hydraulic systems
• Weight: 7.1 lbs
• Length: 8.2 in.
• Width: 4.2 in.
• Height: 10.6 in.
• Flow Range: 4 - 12 gpm
• Optimum Flow Range: 5 - 8 gpm
• Operating Pressure: 1,000 - 2,500 psi
• Torque: 400 ft.-lb. at 8 gpm
• Pressure Port Thd.: 3/4 - 16 SAE O-Ring
• Return Port Thd.: 3/4 - 16 SAE O-Ring

Features:

• Gerotor type motor
• High torque output
• Dual action spool (Open/Closed center operation)
• Proven performance
• 7/16" Tri-ball Quik™ Chuck
• Innovative 3 Part design
• Lightweight tool

Benefits:

• Lifetime warranty of Geroter Motor
• Greater efficiency & longer life than gear motor type tools
• Quik™ Chuck is fastest bit changer
• Provides unmatched power, yet controlable, with 420 ft-lbs of torque @ 5 gpm
• Accommodates standard 7/16" hex drive bits & accessories
• Quickly & easily changes from Open to Closed center operation
• Tool sub-assemblies can be quickly removed/replaced if service required
• Quiter & easier to use
• Light weight impact wrench results in less operator fatigue

Specifications:

• Chuck Type: 7/16" Quik™ Change
• Pressure: 1000 - 2000 psi
• Flow: 4 - 7 gpm
• Operation: Open/Closed center
• Torque: 420 ft-lbs @ 5 gpm
• Motor: Gerotor type
• Max. Back Pressure: 250 psi
• Weight: 7.25 lbs
• Length: 9 in
• Height: 9 in
• Width: 3 in
• Tool Ports: #6 SAE O-Ring

• Compact, lightweight - ideal for line construction applications
• Super Spool™ selector control for use on Open- and Closed-Center hydraulic systems
• Rugged gear motor
• Reversible

Specifications:

• Capacity: 1/2 in. hole - steel, 1-1/16 in. hole - wood
• System: Super Spool™ selector control for use on Open- and Closed-Center hydraulic systems
• Chuck: 1/2 in. key-type
• Weight: 6 lbs.
• Length: 7.5 in.
• Width: 3 in.
• Height: 9 in.
• Flow Range: 4 - 8 gpm
• Operating Pressure: 1,000 - 2,000 psi
• Pressure Port Thd.: 9/16 - 18 SAE O-Ring
• Return Port Thd.: 3/4 - 16 SAE O-Ring
• RPM: 1,300 rpm @ 6 gpm

• Adjustable flow control prevents overspeeding and allows precise control of drilling speed
• Hammer drill in concrete, brick, rock and other difficult to drill materials, drill in wood or steel with auxiliary chuck
• Super Spool™ selector control for use on Open- and Closed-Center hydraulic systems
• Selector for drill or hammer/drill modes
• Rugged gear motor
• Built-in slip clutch to guard against over torque
• Depth gauge and auxiliary handle are removeable for tight areas
• Reversible

Specifications:

• Capacity: Steel 1/2 in. hole, wood 1-1/16 in. hole, concrete 3/4 in. hole, core bits 3 in.
• System: Super Spool™ selector control for use on Open- and Closed-Center hydraulic systems
• Chuck: SDS Plus bit shanks
• Weight: 8.5 lbs.
• Length: 12 in.
• Width: 3.5 in.
• Height: 9.75 in.
• Flow Range: 5 - 10 GPM
• Operating Pressure: 1,000 - 2,000 psi
• Pressure Port Thd.: 3/4 - 16 SAE O-Ring
• Return Port Thd.: 3/4 - 16 SAE O-Ring
• RPM: 775 - 1,100 rpm @ 6.5 gpm
• Blows Per Minute: 3,400 - 4,800 rpm @ 6.5 gpm

• No high pressure intensifier required
• Completes service entrance crimps in seconds
• Accepts Burndy "W" dies and Kearney "O" dies, comes standard with Kearney "D" die
• Head rotates for easy tool positioning
• Operates on either Open- or Closed-Center systems
• Powered in both the advance and retract directions to prevent hang ups
• Relief valve signals operator when crimp is complete
• Relief valve assures 5-ton crimp with 1,400 - 2,500 psi system

Specifications:

• Capacity: 1 in.
• System: Open- and Closed-Center Hydraulic Systems
• Weight: 11.75 lbs.
• Length: 18-7/8 in.
• Width: 4 in.
• Operating Pressure: 1,400 - 2,500 psi
• Crimping Force @ 1,400 psi: 10,000 lb.
• Flow Rate: 3 - 9 gpm
• Pressure Port: 3/4 - 16 SAE O-Ring
• Return Port: 3/4 - 16 SAE O-Ring

• No high pressure intensifier required
• Crimps up to 750 MCM copper and aluminum
• Relief valve signals operator when crimp is complete
• Compatible with dies for: Burndy Y35; Alcoa 12A, 12C, 12HA, 12HAC; Anderson HC-12, HC-12H; Thomas & Betts 12-ton
• Operates on either Open- or Closed-Center systems

Specifications:

• Capacity: 1.65 in.
• System: Open- and Closed-Center Hydraulic Systems
• Weight: 19.7 lbs.
• Length: 20.3 in.
• Width: 5.5 in.
• Operating Pressure: 1,500 - 2,500 psi
• Crimping Force @ 1,500 psi: 24,000 lb.
• Flow Rate: 3 - 9 gpm
• Pressure Port: 3/4 - 16 SAE O-Ring
• Return Port: 3/4 - 16 SAE O-Ring

• No high pressure intensifier required
• Relief valve signals when crimp is complete
• Operates on either Open- or Closed-Center systems
• Compatible with dies for Kearney PH-2 and PH-3 tools

Specifications:

• System: Open- and Closed-Center Hydraulic Systems
• Weight: 19.5 lbs.
• Length: 20.3 in.
• Width: 5.5 in.
• Operating Pressure: 1,500 - 2,500 psi
• Crimping Force @ 1,350 psi: 24,000 lb.
• Flow Rate: 3 - 9 gpm
• Pressure Port: 3/4 - 16 SAE O-Ring
• Return Port: 3/4 - 16 SAE O-Ring

• No high pressure intensifier required
• Crimps cable 500 MCM and larger
• Relief valve signals operator when crimp is complete
• Operates on either Open- or Closed-Center systems
• Compatible with dies for: Kearney PH2*, PH4/PH14; Burndy Y35*, Y46; Teledyne TPU-15H; Thomas & Betts TBM 15 PF*
• Can be converted with adapters for use with Burndy "U" type dies and Kearney PH2 and some WH2 dies

Specifications:

• System: Open- and Closed-Center Hydraulic Systems
• Weight: 28.6 lbs.
• Length: 23.8 in.
• Width: 6.5 in.
• Operating Pressure: 1,500 - 2,500 psi
• Crimping Force @ 1,500 psi: 30,000 lb.
• Flow Rate: 3 - 9 gpm
• Pressure Port: 3/4 - 16 SAE O-Ring
• Return Port: 3/4 - 16 SAE O-Ring

* Requires adapters

• No high pressure intensifier required
• Lightweight tool completes crimps in seconds
• Uses four indentors to make the crimp
• Operates on either Open- or Closed-Center systems
• Head rotates for easy tool and connector positioning
• Powered in both the advance and retreat directions to prevent hang-ups
• Flip-top style uses a pull pin to open head for easy removal from connector

Specifications:

• System: Open- and Closed-Center hydraulic systems
• Weight: 12.7 lbs.
• Length: 20"
• Operating Pressure: 1,400 - 2,500 psi (95 - 170 bar)
• Crimping Force at 1,400 psi (95 bar): 6.2 tons (55 kN)
• Flow Rate: 3 - 9 gpm (11 - 34 lpm)
• Pressure Port: 3/4 - 16 SAE O-Ring
• Return Port: 3/4 - 16 SAE O-Ring

Capacity:

• 5/8" Aluminum Service Entrance Sleeves: #8 AWG - 1/0
• .840" Aluminum Service Entrance Sleeves: #4 AWG - 350 MCM
• Copper Color-Coded Lugs and Splices: #6 AWG - 500 MCM
• Aluminum Color-Coded Lugs and Splices: #6 AWG - 500 MCM

• No high pressure intensifier required
• Lightweight tool completes crimps in seconds
• 6.2 ton capacity, utilizes four indentors to make the crimp
• Operates on either Open- or Closed-Center systems
• Head rotates for easy tool and connector positioning
• Powered in both the advance and retract directions to prevent hang ups
• Flip-top style uses a pull pin to open head for easy removal from the connector

Specifications:

• Capacity:

5/8 in. Aluminum Service Entrance Sleeves: #8 AWG - 1/0

840 in. Aluminum Service Entrance Sleeves : #4 AWG - 350 MCM

Copper color-coded lugs and splices: #6 AWG - 500 MCM

Aluminum color-coded lugs and splices: #6 AWG - 500 MCM

• System: Open- and Closed-Center hydraulic systems
• Weight: 12.7 lbs.
• Length: 20 in.
• Operating Pressure: 1,400 - 2,500 psi
• Crimping Force @ 1,400 psi: 6.2 tons
• Flow Rate: 3 - 9 gpm
• Pressure Port: 3/4 - 16 SAE O-Ring
• Return Port: 3/4 - 16 SAE O-Ring

• Makes quick work of setting poles, asphalt patch and general construction backfill compacting
• Only 3 moving parts for low maintenance
• Reversible on/off valve for Open- and Closed-Center systems
• Standard with kidney-shaped foot

Specifications:

• System: Open- and Closed-Center
• Valve Location: End of hose
• Width: 4 in.
• Flow Range: 4 - 6 gpm
• Operating Pressure: 1,000 - 2,000 psi
• Pressure Port Thread: 9/16 - 18 SAE O-Ring
• Return Port Thread: 3/4 - 16 SAE O-Ring
• Standard Foot Size: 2.5 x 8 in. kidney-shaped
• Blows Per Minute: 1,160 @ 5 gpm

* Unit does not include on/off valve.

• Makes quick work of setting poles, asphalt patch and general construction backfill compacting
• Only 3 moving parts for low maintenance
• Rotate trigger spool for Open- and Closed-Center systems
• Standard with tamper foot

Specifications:

• System: Open- and Closed-Center
• Valve Location: End of Tamper
• Width: 4 in.
• Flow Range: 4 - 6 gpm
• Operating Pressure: 1,000 - 2,000 psi
• Pressure Port Thread: 9/16 - 18 SAE O-Ring
• Return Port Thread: 3/4 - 16 SAE O-Ring
• Blows Per Minute: 1,160 @ 5 gpm

• Cuts hard-to-reach branches from aerial basket or from the ground
• Super Spool™ selector control for use on Open- and Closed-Center systems
• Available in three lengths
• Insulated fiberglass extension tubes, tested to meet OSHA Regulation 1910.269
• Safety features include: two-step trigger guard and fully-covered sprocket guard
• Anti-kickback chain and automatic chain oiler
• Rugged high torque gear motor

Specifications:

• Cutting Capacity: 13 in.
• System: Super Spool™ selector control for use on Open- and Closed-Center hydraulic systems
• Extension Type: Fiberglass - tested to 100 KvA for 5 minutes
• Width: 4 in.
• Flow Range: 5 - 8 gpm
• Operating Pressure: 1,000 - 2,000 psi
• Pressure Port Thread: 9/16 - 18 SAE O-Ring
• Return Port Thread: 3/4 - 16 SAE O-Ring
• Chain Size: .325 in. pitch
• Bar Gauge: .058 in.

• Use for high production utility line clearing and general tree clearing applications
• Super Spool™ selector control for Open- and Closed-Center systems
• Safety features include: hand stop safety collar, trigger guard, two-step safety trigger and branch stop
• Insulated fiberglass extension tube, tested to meet OSHA regulation 1910.269
• Rugged gear motor
• Angular head design makes flush cuts easier and directs chips away from the operator
• 9 in. diameter blade standard

Specifications:

• Cutting Capacity: 3.5 in.
• System: Super Spool™ selector control for use on Open- and Closed-Center hydraulic systems
• Blade Diameter: 9 in.
• Extension Type: Fiberglass - tested to 100 KvA for 5 minutes
• Weight: 9 lbs.
• Overall Length: 82 in.
• Flow Range: 4 - 6 gpm
• Operating Pressure: 1,000 - 2,000 psi
• Pressure Port Thread: 9/16 - 18 SAE O-Ring
• Return Port Thread: 3/4 - 16 SAE O-Ring
• RPM: 5,250 rpm @ 6 gpm

*Caution: Not to be used for ground level operation!

• Model 48200 has Super Sleeve™ for operation with Open- or Closed-Center systems
• Use on utility line clearing and selective pruning of shade trees
• Heavy cut capacity cuts branches up to 2 in.
• Trigger guard
• Insulated fiberglass extension tubes, tested to meet OSHA Regulation 1910.269
• Full power return

Specifications:

• Cutting Capacity: 2 in.
• Extension Type: Fiberglass - tested to 100 KvA for 5 minutes
• Weight: 12 lbs.
• Overall Length: 86 in.
• Width: 6-1/4 in.
• Flow Range: 4 - 6 gpm
• Operating Pressure: 1,000 - 2,000 psi
• Pressure Port Thd.: 9/16 - 18 SAE O-Ring
• Return Port Thd.: 3/4 - 16 SAE O-Ring

• Ideal for large trimming applications and cut-up removal jobs
• Super Spool™ selector control for Open- and Closed-Center systems
• Chain and bar can be adjusted without removing sprocket cover
• Sprocket cover can be removed without tools for easy saw cleaning
• Handle position can be oriented to horizontal, 60 or 30 degrees relative to bar and chain according to operator preference
• Rugged gear motor and expanded chip exit area
• Automatic chain oiler can be adjusted without tools
• Safety features include: two-step safety trigger, high impact polymer front handle/shroud, wide lower handle protects hands/knuckles, chain catcher stops chain rotation
• Reduced kickback bar and chain
• Supplied with 12 in. steel braided whip hoses (couplers not included)

Specifications:

• System: Super Spool™ selector control for use on Open- and Closed-Center hydraulic systems
• Weight: 6.7 lbs. power head only with bar 9.5 lbs.
• Width: 10 in.
• Flow Range: 4 - 8 gpm
• Operating Pressure: 1,000 - 2,000 psi
• Pressure Port Thread: 9/16 - 18 SAE O-Ring
• Return Port Thread: 3/4 - 16 SAE O-Ring
• Chaing Size: .3/8 in. pitch
• Bar Gauge: .050"

• A deep rod opening and smooth operation ensures that the driver will not jump off the rods
• Lightweight allows easy mounting on top of rods
• Can be used with Open- and Closed-Center hydraulic systems
• Dual guide rods provide excellent control for driving rods straight, and the remote on/off valve makes it easy to control the depth of the rod

Specifications:

• Hydraulic System: Open- and Closed-Center
• Weight: Power Unit Only - 45 lbs. w/ Hoses and Control Valve - 53 lbs.
• Length: 25-1/2"
• Flow Range: 5-8 gpm
• Blows/Min @ 8 gpm: 1740
• Maximum Input Pressure: 2000 psi
• Hose Length: 70"
• On/Off Valve Pressure Ports: 9/16 - 18 SAE O-Ring Boss

• Compact, lightweight design
• High impact strainer housing
• Up to 275 gpm
• Carrying handle
• Self-priming
• Can run dry without damage

Specifications:

• System: Open- and Closed-Center
• Capacity: Up to 275 gpm [at 7 gpm and a 10' head height]
• Intake Port: 1-15/16"
• Discharge Port: 2" NPFT
• Strainer: 2-5/8 x 5-5/8" - 3/8" openings
• Weight: 9 lbs.
• Height: 12.5" over handle
• Width: 7.5" diameter
• Flow Range: 5 - 8 gpm
• Operating Pressure: 0 - 2,000 psi
• Pressure Port Thread: 9/16 - 18 SAE O-Ring
• Return Port Thread: 3/4 - 16 SAE O-Ring

• High impact strainer housing
• Self-priming
• Up to 400 gpm
• Carrying handle
• Can be run dry without damage

Specifications:

• System: Open- and Closed-Center
• Capacity: Up to 400 gpm [at 7 gpm and a 15' head height]
• Intake Port: 1-1/2" NPT
• Discharge Port: 2-1/2" NPT
• Strainer: 7" x 2.5"
• Weight: 23.5 lbs.
• Height: 16"
• Width: 12" diameter
• Flow Range: 4 - 8 gpm
• Operating Pressure: 0 - 2,000 psi
• Pressure Port Thread: 9/16 - 18 SAE O-Ring
• Return Port Thread: 3/4 - 16 SAE O-Ring

• Lighter than typical 3 in. trash pumps
• All aluminum body is lightweight and durable
• Compact, under 12 in. diameter to easily fit into small areas
• Open- and Closed-Center operation runs off a variety of power sources
• Self-priming submersible pump can be placed and operated quickly
• Passes up to 3 in. solids minimizing pump blockage from debris
• Can be run dry without damage for longer working life
• Carry handle with lifting eye makes it easy to transport, move, lift and lower

Specifications:

• Hydraulic Pressure Port: 1/2 in. Male NPT
• Hydraulic Return Port: 1/2 in. Male NPT
• Mass-Weight: 24 lbs.
• Width (diameter): 11.87 in.
• Height (with handle): 14.18
• Maximum Trash Diameter: 3 in.
• Pump Inlet Port: 3.125 in.
• Pump Discharge Port: 3 in. Female NPT
• Type of Hydraulic System: Open- or Closed-Center
• Minimum Flow: 7 gpm
• Recommended Flow: 8 - 10 gpm
• Maximum Flow: 10 gpm
• Filtration: Nominal
• Pressure Relief Setting: 2500 psi
• Back Pressure (maximum)*: 200 psi

* 200 psi is the maximum agreed standard back pressure for the HTMA.

• Great for breaking sidewalks and curbs or driving ground rod, and for other small demolition jobs
• Clean modular design with few protrusions to irritate operators legs
• High blow energy provides maximum breaking power
• Integral rubber damper reduces chisel noises
• Low noise and vibration levels
• AVS tools have patented spring-dampened handles that reduce vibration transmitted to the operator by 80%-90%
• Two-step trigger

Specifications:

• Weight: 53 lbs.
• Sound Power Level: LWA=110 dB
• Blow Energy: 63 ft-lb
• Blow Frequency: 2160/min
• Oil Flow: 5-8 gpm
• Length: 28.5"
• Hydraulic System: Open-Center
• Pressure & Return Ports: 1/2" BSP
• Whip Hose Threads: 1/2" NPTF

• High blow energy provides maximum breaking power that can handle big demolition tasks with ease
• Clean modular design with few protrusions to irritate operator's legs
• High blow energy provides maximum breaking power
• Integral rubber damper reduces chisel noise
• Low noise and vibration levels
• AVS tools have patented spring-dampened handles that reduce vibration transmitted to the operator by 80%-90%
• Two-step trigger

Specifications:

• Weight: 55 lb.
• Sound Power Level: LWA=112 dB
• Blow Energy: 81 ft.-lb.
• Blow Frequency: 1860/min
• Oil Flow: 5-8 gpm
• Length: 30"
• Hydraulic System: Open-Center
• Pressure & Return Ports: 1/2" BSP
• Whip Hose Threads: 1/2" NPTF

• High blow energy provides maximum breaking power that can handle big demolition tasks with ease
• Clean modular design with few protrusions to irritate operator's legs
• High blow energy provides maximum breaking power
• Integral rubber damper reduces chisel noise
• Low noise and vibration levels
• AVS tools have patented spring-dampened handles that reduce vibration transmitted to the operator by 80%-90%
• Two-step trigger

Specifications:

• Weight: 71 lbs.
• Sound Power Level: LWA=113 dB
• Blow Energy: 118 ft.-lb.
• Blow Frequency: 1500/min
• Oil Flow: 7-9 gpm
• Length: 30"
• Hydraulic System: Open-Center
• Pressure & Return Ports: 1/2" BSP
• Whip Hose Threads: 1/2" NPTF

Use with Breaker Cat. No.

• On-board air compressor provides air to clean dust out of holes
• Drill rotation speed is adjustable from 0 to 400 rpm with a 4-position dial; tool can be operated without rotation
• Has vibration isolated and cushioned handles to reduce operator fatigue
• Simple design provides excellent durability and simple repair
• Drills a 2-1/2" diameter hole up to 10 feet deep
• Supplied with steel braided whip hoses

Specifications:

• Hydraulic System: Open-Center
• Weight: 44 lbs.
• Length: 25"
• Width: 16"
• Whip Hoses: 3/8" NPTF x 12"
• Chuck Size: 7/8" x 4-1/4"
• Hydraulic Flow: 5 - 7 gpm
• Operating Pressure: 1,275 - 1,700 psi
• Blows Per Minute: 1,400 maximum (varies with rotation speed)
• Drill Rotation Speed: 0 - 400 rpm
• Air Flow: 2.8 cu. ft/min
• Air Pressure: 29 psi (2 bar)

• Operates off other equipment's hydraulic accessory circuits - no need for a separate power unit
• Accepts up to 30 gpm for running off most Skid-steer, tractors and loaders
• Variable flow adjustment allows precise control for tool operation
• Intergral pressure relief valve helps protect hydraulic equipment and tools
• All aluminum body design is lightweight and provides better heat dissipation
• Low profile, compact unit is unobtrusive and easy to install
• All tool ports have O-ring boss and accept industry standard hoses and couplers

Specifications:

• Hydraulic Ports: Power Source Side - Pressure: 1-1/16 in. NPT - SAE O-Ring Boss
• Power Source Side - Return: 1-1/16 in. NPT - SAE O-Ring Boss
• Tool Side - Pressure: 3/4 in. - 16 SAE O-Ring Boss HTMA Flush Face Coupling
• Tool Side - Return: 3/4 in. - 16 SAE O-Ring Boss HTMA Flush Face Coupling
• Hydraulic Flow and Pressure: Maximum Output Flow: 10 gpm
• Maximum Output Pressure: 2150 psi
• Temperature Range: -30° to 140° F
• Length: 8.79 in.
• Width: 6.72 in.
• Height: 5.03 in.
• Mass/Weight: 8.3 lbs.
• Maximum Input Flow: 30 gpm
• Maximum Input Pressure: 3000 psi

• Electric key-start 20 hp Honda OHV engine with low-oil shutdown
• Variable oil flow to 10 gpm
• Oversized oil cooler and electric fan ensures cool running
• Engine hour meter and tachometer
• Hydraulic oil level sight gauge and 10 micron oil filter
• Tubular frame protects components and allows easy access to maintenance points
• Integral grab rails for lifting the unit into trucks and trailers
• Heavy-duty lifting eye
• HTMA flat-face hydraulic couplers
• Easy access service points for engine oil, fuel, battery, and oil filter
• Sealed lead-acid battery

Specifications:

• Horsepower: 20 at 3,600 rpm
• System: Open-Center
• Rated Flow: 5 - 10 gpm
• Rated Pressure: 2,000 psi
• Fuel: Gasoline 3.3 gal
• Hyd Oil Capacity: 3.1 gal
• Dry Weight: 259 lbs.
• Length: 34"
• Width: 31"
• Height (handle folded): 32"

• Can drive a variety of post sizes from small delineater posts up to 3-1/2" round posts including square, "U" channel, breakaway stubs, round, "T" fence, and wood
• Quick change front head design accommodates adapters for different types of posts
• Dual guide handles for good directional control
• A deep post opening and smooth operation ensures that the driver will not jump off posts
• Can be used with Open and Closed-Center hydraulic systems
• Available with integral trigger or remote on/off valve
• U.S. Patent #6,626,247

Specifications:

• Hydraulic System: Open- and Closed-Center
• Weight w/UA Adapter and Hoses: 75 lbs
• Length: 32"
• Flow Range: 5-8 gpm
• Blows Per Minute @ 8 gpm: 1500
• Maximum Input Pressure: 2000 psi
• Hose Length on HPV-HV models: 70"
• On/Off Hose Connection Sizes (HPD-T):

Pressure Hose - 1/2" NPTF

Return Hose - 1/2" NPTF

• Valve Connection Port Sizes (HPV-HV):

On/Off Valve Pressure Port - 9/16-18 SAE O-Ring Boss

On/Off Valve Return Port - 9/16-18 SAE O-Ring Boss

• Uses serrated jaws or wraparound, high-strength alloy chain
• Able to pull most any post sizes and shapes
• Faster and easier than conventional manual methods

Specifications:

• System: Open-Center
• Lift Capacity: 9,800 lbs.
• Stroke: 5 in.
• Chain: 9/32 in. alloy
• Weight: 70 lbs.
• Length: 10.5 in.
• Height: 26 in. retracted
• Width: 10 in.
• Flow Range: 4 - 6 gpm
• Operating Pressure: 1,000 - 2,000 psi
• Pressure Port Thread: 9/16 - 18 SAE O-Ring
• Return Port Thread: 3/4 - 16 SAE O-Ring

• Easily cuts concrete, stone, or steel when equipped with the appropriate blade (blade not included)
• Comes complete with a threaded water hose port
• 24 in. whip hoses
• Auxiliary handle
• Rugged gear motor
• Adjustable debris guard
• Optional three-wheel car (H6245SC/49848) available

Specifications:

• System: Open-Center
• Cutting Capacity: 5.25 in. with 14 in. blade
• Blade Diameter: 14 in.
• Arbor Shaft Diameter: 1 in.
• Weight: 21 lbs.
• Length: 26.5 in.
• Width: 5.5 in.
• Flow Range: 5 - 8 gpm
• Operating Pressure: 1,000 - 2,000 psi
• Blade Speed: 4,100 rpm at 8 gpm
• Pressure and Return Port Thread: 3/8 NPTF (Tool), 1/2 NPTF (Hose End)

Low pressure hose - certified nonconductive orange rubber, double rayon braid - working pressure 2,250 psi tested to 75 Kv/ft for 5 minutes.

Hose assemblies can be applied directly to the tool without the use of body assemblies or nose pieces, eliminating the quick-disconnect feature by ordering one each.

For use in place of quick disconnect body assemblies on tool, allows any type coupling to be used.

The 15GBM is a gas powered pump that produces 10,000 PSI of hydraulic pressure. It is designed to handle any high pressure tool up to and including the 60 ton press. The two-stage pumping system allows for rapid ram advance. The "suc-o-matic" valve helps tools retract faster. The manual control has three settings: advance, hold and retract. Whether making one crimp or 1,000 crimps, the 15GBM is the lightweight, portable answer.

Features:

• 10,000 PSI high-pressure pump
• Powered by a 3.75 HP Briggs and Stratton engine
• Manual control valve
• Designed to operate single acting tools
• High pressure relief valve
• Pressure matched quick coupler supplied
• Protective carrying cage
• "Suc-o-matic" valve reduces retraction time
• Sight gauge to determine hydraulic oil level

Specifications:

• Oil Delivery per minute:

400 cu in @ 600 psi

50 cu in @ 10,000 psi

• Oil Reservoir: 2 Gallons
• Overall Length: 12.25 in
• Overall Width: 12.25 in
• Overall Height: 20.25 in
• Pump Weight with Oil: 53 lbs.

30 GB-M

• 6 HP Briggs/Stratton engine
• 10,000 PSI high pressure pump
• Manual control valve
• High pressure safety relief valve
• Single acting mode only
• Pressure matched female quick couplers supplied
• Factory filled 2 gallon reservoir w/ sight glass
• Protective carrying frame

Specifications:

• Electrical Control: Single push button switch
• Oil Delivery Per Minute: 430 cu in at 400 psi
• Oil Reservoir: 2 gallons
• Overall Width: 19.75 in.
• Overall Length: 21.75 in.
• Overall Height: 24.50 in.
• Pump Weight With Oil: 154 lbs.

The 250M10C Hydraulic Booster is a lightweight, compact intensifier that operates from an external oil source. It uses the oil from a low pressure hydraulic system such as a bucket truck. It is designed to operate any single acting 10,000 PSI tool. It can be mounted on the side of the bucket. These units can be operated in any position on either open or closed center hydraulic systems.

Features:

• Designed to intensify low-pressure systems to 10,000 PSI
• No reservoir to maintain, uses low pressure oil supply
• Manual control valve
• Designed to operate single acting
• High-pressure relief valve
• Pressure matched quick coupler supplied
• Integrated pressure gauge
• Compact

Specifications:

• Input Pressure: 300 - 2,000 psi
• Input Flow Range: 0 - 10 gallons per minute
• Output Pressure: 10,000 psi
• Oil Delivery(output pressure): 230 cu in per minute
• Output Flow Range: 0 - 2 gallons per minute
• Output Flow Ratio: 1:5
• Output Pressure Ratio: 5:1
• Overall Length: 9.65 in.
• Overall Width: 5.15 in.
• Overal Height: 9.04 in.
• Pump Weight with oil: 27 lbs.

The 250MDA10C Hydraulic Booster is a lightweight, compact intensifier that operates from an external oil source. It uses the oil from a low pressure hydraulic system such as a bucket truck. It is designed to operate any double acting 10,000 PSI tool. It can be mounted on the side of the bucket. These units can be operated in any position on either open or closed center hydraulic systems.

Features:

• Designed to intensify low-pressure systems to 10,000 PSI
• No Reservoir to maintain, uses low pressure oil supply
• Manual control valve
• High-pressure relief valve
• Pressure matched quick coupler supplied
• Integrated pressure gauge
• Compact

Specifications:

• Input Pressure: 300 - 2,000 psi
• Input Flow Range: 0 - 10 gallons per minute
• Output Pressure: 10,000 psi
• Oil Delivery (output pressure): 230 cu in per minute
• Output Flow Range: 0 - 2 gallons per minute
• Output Flow Ratio: 1:5
• Output Pressure Ratio: 5:1
• Overall Length: 9.65 in.
• Overall Width: 5.15 in.
• Overall Height: 9.04 in.
• Pump Weight with oil: 27 lbs.

Dynapress®

Prefilled 1/4" I.D. synthetic reinforced pressure hose with 3/8" quick couplers on either end, complete with dust caps and plastic end guards. These non-conductive hoses (100 KV per ft.) are certified to S.A.E. standard J343 with a working pressure of 10,000 PSI, bursting pressure of 40,000 PSI and are color coded "International Orange" for visual identification. Stock length 15 feet. Standard Pressure Hose is supplied with male coupler on each end.

• May be directly connected to the tool or used remotely with hoses

Compact

• 4-way, 3-position valve
• 3,000 - 4,000 psi return line ground dump safety valve
• Built-in hold feature
• Controlled advance
• Single-acting valve available to use with existing single-acting tools

Specifications:

• Max. Oper. Pressure: 10,000 psi Return Relief
• Pressure: 5,000 psi
• Input Flow Range: 3 - 8 gpm
• Weight: 3 lbs.
• Length: 9.5 in.
• Width: 2 in.
• Height: 3.5 in.
• Port Size - Inlet: 1/4 - 18 NPTF
• Port Size - Tool: 1/4 - 18 NPSM
• Couplers: High Pressure Quick-Disconnects included, 10,000 psi

The BURNDY® RHCC129ACSR remote hydraulic cable cutter incorporates a specialized latch style cutting head that allows interference-free closure for mid-span cuts. The RHCC129ACSR with its precision cutting blades is capable of cutting up to 1.29" diameter bare or insulated copper and aluminum cable, 1113 ACSR, 5/8" ground rod, 1/2" rebar, 5/8" diameter soft steel bolts, 1/2" standard guy strand, and up to 3/8" EHS guy strand.

The RHCC129ACSR is provided witha 5-year limited warranty (excluding blades).

Features and Benefits:

• Specialized latch head design
• Interference free closure for mid-span cuts
• Precision cutting blades
• For clean cuts on Cu/AL, ACSR, ground rods, rebar, guy strand, and soft steel bolts
• High strength steel cylinder, for durability and long life
• Lightweight ergonomic design allows one hand operation
• User has one hand free to manipulate material to be cut
• Durable canvas carrying bag, provides tool protection and stores all accessories
• 5-year limited warranty on tool (excluding blades)
• Customer satisfaction and support

Specifications:

• Operating Pressure: 10,000 psi
• Tool Weight: 5.85 lbs.
• Length: 11.25"
• Width: 3.7"

Type Y750BH HYPRESS™ 10,000 PSI

 

12 ton remote power operated hydraulic tool. The Y750BH HYPRESS incorporates a wide mouth (1.65") C-shaped head for all compression applications. The hook style head provides for easy tapping, splicing, and terminating of overhead lines as well as the full range of HYGROUND compression grounding system connectors, NEC cable connections and N30-N650 Navy Cable applications.

Benefits:

• Covers a wide range of applications and provides easy tool removal from continuous conductors with it's C-shaped head
• Easy die change out and retention within exposed positive die lock buttons
• Uses all standard Burndy U-dies
• Y750BH-2 provides molded rubber covering on head, body and hose fittings
• Hot stick adapter sold separately (PT23484)
• Infinitely rotatable head, so hydraulic couplers won't easily loosen
• 5 year limited warranty

 

 

 

Catalog#	Operating Pressure	Force Developed	Jaw Opening	Length	Head Width
Y750BH	10,000 psi	12 Tons	1.65"	12"	4.43"
Y750BH-2	10,000 psi	12 Tons	1.65"	19.93" (includes boot)	4.92"
PT23484	-	-	-	-	-

Type Y46 & Y46C HYPRESS™ 10,000 PSI

• Interchangeable adapters permit the use of a wide variety of die types for all common crimping applications
• Accepts Kearney PH4/PH14 dies without adapters
• Lightweight
• Zinc-plated head resists corrosion better than other finishes
• Hot stick attachment point is standard
• Operates with most 10,000 psi hydraulic sources
• Equipped with 3/8" male screw type 10,000 psi coupler
• Includes steel carrying case

Specifications:

• Capacity:

Color-Coded copper lugs and splices: #8 to 1000 kcmil

Color-Coded aluminum lugs and splices: #8 to 1000 kcmil

• Crimping Force at 10,000 psi: 30,000 lbs
• Length: 15"
• Width: 3"
• Height: 5-3/8"
• Weight: 14.1 lbs
• Operating Pressure: 10,000 psi

Type Y45 HYPRESS™ 10,000 PSI

 

The Y45 series is designed for remote hydraulic operation. A C-shaped head design provides easy installation of tap and splice connectors. The hook style head with extensive ram travel operates easily on large distribution and transmission conductors. Together with accessories, the Y45 Series tooling may be used on overhead lines.

Benefits:

• Easy connector installation and tool removal from line conductors with the open C-shaped head
• Easily lifted into working position using lifting eye
• Easy die changing plus secure die alignment is provided with the positive die lock buttons
• Rapid assembly and disassembly is provided with the quick disconnect hydraulic coupler
• Rugged design provides long life expectancy
• The Y45-1 head has molded rubber covering
• Easy tool handling plus hydraulic coupler protection is provided with the rubber boot
• 5 year limited warranty

 

Catalog#	Operating Pressure	Force Developed	Max. Width	Max. Height	Description
Y45	10,000 psi	15 Tons	7.25"	14.25"	-
Y45-1	10,000 psi	15 Tons	7.75"	14.50	Molded Covering

HYPRESS™

 

Single and Double Acting Hydraulic Tool Designs

The Y60BHU HYPRESS™, single acting and Y60BHU-D HYPRESS™, double acting, are both designed to provide fast, easy operation plus a durable and substantially longer design life expectancy. Both Y60BHU and Y60BHU-D HYPRESS tools accommodate the same "L" dies. The "L" dies are designed for copper and aluminum code cables and aerial conductor sizes though 2500 kcmil and will accommodate ACSR through 2156 (84/19) str. Five-year limited warranty.

Benefits:

• Easy to carry with heavy duty handle
• Easy to remove splices with nest that pivots open
• Safety and security is provided with captive locking pin for nest die
• Long life expectancy (50,000 cycles) with heavy duty steel frame
• Fast easy die changing and secure die positioning with positive die release locking pins
• Faster retraction with double acting hydraulic system (Y60BHUD)
• Protected male coupler with captive cap
• Stability is provided with sturdy steel base
• Easy, less costly repairs with fewer parts that are easily accessible. Ex: Bottom die holder
• 5-year limited warranty

Specifications:

• Force Developed: 60 Tons
• Operating Pressure: 10,000 PSI
• Hydraulic Oil: BURNDY Alfluid
• Life Expectancy: 50,000 cycles min.
• Height: 16.62"
• Weight (less case): 70 lbs.
• Shipping Weight: 97 lbs.

 

Catalog#	Description
Y60BHU	Single Acting
Y60BHU-D	Double Acting

The model 60A-GSC and 60A-FT-GSC compressors are portable 60 ton construction and maintenance tools designed to cover a full range of compression accessories requiring die sizes up to and including 40AH. The 60A-FT-GSC features an integral hinged head with eyes suitable for hot line work. These compressors work best with the 30 Series gas pumps and the 25 Series Boosters.

Do Not Operate any compression tools without dies.

Features:

• 60 tons of force
• Larger capacity for transmission and distribution applications
• Easy die set installation
• Capacity for all 60 ton U or shell-type dies
• Optional hinged flip-top head w/ eyes suitable for hotline work
• Metal carrying case
• Lightweight
• Portable
• Includes ground stand
• Pressure matched female quick coupler supplied
• Compression Force: 62.8 US Tons
• Operating Pressure: 10,000 psi
• Crimping Capacity: 1590 MCM
• Overall Length: 9.00 in.
• Overall Width: 8.50 in.
• Overall Height: 17.75 in.
• Tool Weight: 42 lbs.

Gator-Plus™

 

• New breakthrough hydraulic pump design results in an extremely compact battery-powered crimping tool with capacity to 250 kcmil copper color-coded connectors; also crimps 5/8 and 840 service entrance connectors
• Special compact 9.6 volt Ni-Cd battery reduces weight and size
• Slim profile and light weight provide for one-hand operation
• Can complete approximately 85 crimps per battery charge with 4/0 copper connectors
• Ram automatically retracts to signal that crimp is complete
• Ram can be retracted in mid-cycle to adjust connector
• Flip-open crimping head rotates 360°
• UL and cUL Classified with Anderson, Blackburn, Burndy, ILSCO, Panduit, Penn-Union, and Thomas & Betts copper color-coded code connectors
• Includes two batteries, battery charger, and molded carrying case

Specifications:

• Capacity: #8 AWG to 250 kcmil copper color-coded connectors, 5/8 service entrance connectors, 840 service entrance connectors
• Crimping Force: 7,900 lbs.
• Length: 14"
• Width: 3-1/8"
• Weight: 3.6 lbs.
• Crimp Cycle Time: ~4 seconds
• Battery: 9.6 volt 1.3 Ah Ni-Cd battery
• Battery Charge Time: 1 Hour

 

Catalog#	Description
EK410-11/02033	4-Ton Battery-Powered Crimping Tool, 120 V Charger
EK410-12/02034	4-Ton Battery-Powered Crimping Tool, 12 V Charger

Gator®

 

• Slim profile and light weight permit one hand operation
• Crimping jaws automatically open to signal that crimp is complete
• Crimping jaws can be opened in mid-cycle to adjust connector
• When equipped with CJD3 crimping jaws, can be used with all industry "W" style crimping dies; when equipped with CJK crimping jaws
• Can be used with dies for Kearney Type "O" tools
• Crimping jaws are PVC coated on outside edges
• Carrying strap makes tool easy to carry and to hang in buckets
• Interchangeable crimping jaws rotate 360°
• Two batteries, battery charger, and molded carrying case included
• Can cut up to 4/0 ACSR cable when equipped with KD6-27 cutter dies

Specifications:

• Weight: 5.4 lbs.
• Length: 18"
• Width(head open): 4"
• Crimping Force: 5 tons
• Battery: 9.6 Volt, 1.3 Ah
• Crimp Cycle Time: ~ 6 seconds
• Battery Charger Time: 1 hour

 

Catalog#	Description
EK425-D11/11311	Crimping Tool w/CJD3 Crimping Jaws w/120 Volt Battery Charger
EK425-D12/11312	Crimping Tool w/ CJD3 Crimping Jaws w/12 Volt Battery Charger

Gator™ Pro ECCX

 

• Nickel-metal hybride battery (Ni-MH) delivers up to 140 cycles per charge
• Equipped with a spare battery, a choice of either a 120V, 12V or 220V one-hour charger, and a high-impact molded carrying case
• 360 degree rotating head adjusts to your work position
• Lightweight, plus ergonomic-angled handle for comfortable, low-stress use
• Cycles in seconds with two-speed hydraulic pump, maximizing productivity
• Automatic retraction when crimping and cutting cycles are complete
• Uses all CCX blades and adapters
• U.S. Patent #6,206,663 and Patent Pending

Specifications:

• Crimping Force: 6 tons
• Length: 14-3/4"
• Height: 12-1/8"
• Battery: 12 Volt, 2.2Ah, Ni-MH
• Battery Charge Time: 1 hour

 

Catalog#	Description
ECCX12	Battery-powered Tool with CCX Head, 2 Ni-MH Batteries, 12 Volt Charger, and High-Impact Molded Carrying Case

Optional, all in pairs except punch driver.

Type BATOOL™ BCT500-HS

 

The Burndy BCT500-HS, Battery Crimp Tools, compact, lightweight design, provides easy one hand operation for ram advance and retract. The BCT500-HS features an integral 180 degree rotatable latch head design affording greater clearance, accommodating tight areas, and has a permanent "D3" die groove that also serves as a seat for all "W", "W-VT" and "X" style dies. Industry standard 12 V-DC battery voltage, and recharging in less than 60 minutes, provides up to 1,000 recharge cycles per battery, for longer working life.

Features:

• No electronics
• One-handed ram advance/retract operation
• Specialized latch head design
• 180 degree head rotation
• Variable speed trigger
• Mechanical ram release
• Ergonomic handle design
• Light weight tool
• Audible "pop-off" indicates properly completed crimps
• Durable metal carry case
• 1 year warranty

Specifications:

• Crimp Force: 6 Tons
• Tool Weight: 8.36 lbs.
• Length: 13.4 in.
• Width: 3.125 in.
• Height: 11in.
• Operating Voltage: 12 V-DC
• Crimp Time: Approx. 8 seconds
• Recharge Time: < 60 mins.

 

Catalog#
BCT500-HS

PATRIOT™

 

The BURNDY® PAT600-18V battery powered crimping tool provides a powerful 6 tons of crimping force and completes a crimp in approximately 3 seconds. The PAT600-18V is compact, easy to use and incorporates the latest in battery tool technology. The PAT600-18V tool incorporates a specialized latch style head with enhanced working stroke and clearance capabilities. The specialized head allows interference-free closure on tap connections up to the BURNDY® YHD-400 size including 350 AL connectors. Die selection with this tool includes all BURNDY® "W" and "W-VT" style dies which seat in the permanent "D3" crimping groove. Installation applications include #8 AWG to 600 kcmil copper lugs and splices, #8 AWG to 350 kcmil aluminum lugs and splices (YA-A and YS-A), and up to 4/0 aluminum tap connections. The permanent "D3" groove and 180 degree rotatable head are standard on the PAT600-18V.

Each PAT600-18V tool uses BURNDY® dies and off-the-shelf connectors available world-wide. The PAT600-18V comes equipped with a high impact formed carrying case to hold the tool, a battery charger and two batteries. The case houses up to 10 "W" dies (dies purchased separately). The PAT600-18V uses industry standard batteries and chargers. The PAT600-18V comes complete with a 2-year limited warranty and one year on batteries and charger.

Features and Benefits:

• Battery powered crimp technology
• Easy tool operation and portabiliy
• Advance design high speed pump completes crimp in approximately 3 seconds
• Longer life, efficiency, and reliabilty
• Ergonomic design allows one hand operation for ram advance and ram retraction
• User always has one hand free to manipulate connector and conductor
• Variable speed trigger
• Provides flexibility is speed of ram advance
• Ram holds position when trigger is released
• Provides ability to hold the connector between dies and check for proper alignment prior to crimping action
• Mechanical ram release
• Reliable ram release (no battery power consumption)
• Specialized latch head design
• Provides enhanced clearance on tap connectors when compared with competitive designs

Specifications:

• Crimp Force: 6 Tons
• Tool Weight: 10.9 lbs.
• Length: 14.5"
• Width: 3.5"
• Height: 13.75"
• Operating Voltage: 18V-DC
• Crimp Time: Approx. 3 seconds
• Recharge Time: < 45 mins.

 

Catalog#	Description
PAT600-18V	See features for item description.
PT208620	Lanyard
WDIETREE	W Die Holder
BAT18V	Battery: Hi-capacity(2200 mA-hr)
BAT18VLED	Battery with LED light:(3000 mA-hr)
PATCHGR18V	Charger: 120V-AC
BCT/PATDCCHGR	Charger: 12/24V-DC
PATCHGR250V	Charger: 240/250V-AC

PATRIOT™

PATRIOT™

 

The BURNDY® PATCUT129ACSR-18V battery powered cutting tool is compact, fast, easy to use and incorporates the latest in battery tool technology. The ergonomic design allows one hand operation so that the other is free to manipulate the conductor in the proper cutting position. The PATCUT129ACSR-18V incorporates a specialized latch style cutting head that allows interference-free closure for mid-span cuts. The cutter head rotates 180-degrees to allow users to get into tight areas easier. The PATCUT129ACSR-18V is capable of cutting up to 1.29" diameter copper and aluminum cable, 1113 ACSR, 5/8" ground rod, 1/2" rebar, 5/8" diameter soft steel bolts, up to 1/2" standard guy strand, and up to 3/8" EHS guy strand.

The PATCUT129ACSR-18V operates on industry standard 18-volt Ni/MH batteries that eliminate voltage depression or "memory" issues. The PATCUT129ACSR-18V comes equipped with a high impact formed carrying case to hold the tool, a tool retention lanyard, a battery charger and two batteries. The PATCUT129ACSR-18V is provided with a 2-year limited warranty (excluding blades), and 1-year on batteries and charger.

Features and Benefits:

• Battery powered cutting technology
• Easy tool operation and portability
• Advance design high-speed pump completes tough cuts faster
• Longer life, efficiency, and reliability
• Specialized latch head design
• Interference free closure for mid-span cuts
• Ergonomic design allows one hand operation
• User has one hand free to manipulate material to be cut
• 180 degree head rotation
• Versatile head positioning allows user to get into tight areas easier
• Mechanical ram release
• Reliable ram release (no battery power consumption)
• Operates on 18 volt Ni-MH batteries
• Eliminates voltage depression or "memory" issues
• Durable high impact formed carrying case, provides tool protection and stores all accessories
• 2-year limited warranty on tool (excluding blades) and 1 year on batteries and charger
• Customer satisfaction and support

Specifications:

• Tool Weight: 11 lbs.
• Length: 14.5"
• Width: 3.5"
• Height: 13.5"
• Operating Voltage: 18 V-DC
• Recharge Time: < 45 mins.

 

Catalog#	Description
PATCUT129ACSR-18V	See features for item description.
Accessories
PT208620	Lanyard
BAT18V	Battery: Hi-capacity(2200 mA-hr)
BAT18VLED	Battery with LED light:(3000 mA-hr)
PATCHGR18V	Charger: 120V-AC
BCT/PATDCCHGR	Charger: 12/24V-DC
PATCHGR250V	Charger: 240/250V-AC

PATRIOT®

 

The BURNDY® PATCUT245CUAL-18V battery powered cutting tool is compact, fast, easy to use and incorporates the latest in battery tool technology. The ergonomic design allows one hand operation so that the other is free to manipulate the conductor in the proper cutting position. The PATCUT245CUAL-18V incorporates a specialized latch style cutting head that allows interference-free closure for mid-span cuts. The cutter head rotates 180 degrees to allow users to get into tight areas easier. The PATCUT245CUAL-18V is capable of cutting up to 2.45" diameter copper and aluminum cable.

The PATCUT245CUAL-18V operates on industry standard 18-volt Ni-MH batteries that eliminate voltage depression or "memory" issues. The PATCUT245CUAL-18V comes equipped with a high impact formed carrying case to hold the tool, a tool retention lanyard, a battery charger and two batteries. The PAT-CUT245CUAL-18V is provided with a 5-year limited warranty (excluding blades) and 1-year on batteries and charger.

Features and Benefits:

• Battery powered cutting technology
• Easy tool operation and portability
• Advance design high-speed pump completes tough cuts faster
• Longer life, efficiency, and reliability
• Specialized latch head design
• Interference free closure for mid-span cuts
• Ergonomic design allows one hand operation
• User has one hand free to manipulate material to be cut
• 180-degree head rotation
• Versatile head positioning allows user to get into tight areas easier
• Mechanical ram release
• Reliable ram release (no battery power consumption)
• Operates on 18-volt Ni/MH batteries
• Eliminates voltage depression or "memory" issues
• Durable high impact formed carrying case, provides tool protection and stores all accessories
• 5-year limited warranty on tool (excluding blades) and 1-year on batteries and charger
• Customer satisfaction and support

Specifications:

• Tool Weight: 14.5 lbs With Battery
• Length: 18"
• Width: 3.75"
• Height: 14.75"
• Operating Voltage: 18 V-DC
• Recharge Time: < 45 mins.

 

Catalog#	Description
PATCUT245CUAL-18V	See features for item description.
Accessories
PT10044980	Carrying Case
PT208620	Lanyard
BAT18V	Battery: Hi-capacity(2200 MA-hr)
BAT18VLED	Battery with LED light: (3000 mA-hr)
PATCHGR18V	Charger: 120V-AC
BCT/PATDCCHGR	Charger: 12/24V-DC
PATCHGR250V	Charger: 240/250V-AC
PT10038657	Replacement Blade:(Moving Blade)
PT10040663	Replacement Blade:(Fixed Blade)

 

PATRIOT™

Model REC-458U ROBO*CRIMP™

 

The Huskie REC-458U is the same design as the REC-358 with the addition of an upgraded hydraulic circuit. The new rapid advance feature allows the operator quicker compression cycles. In addition to the rapid advance feature, it also has incorporated an electronic counter that will allow a service technician to read the number of compression cycles the tool has made. Also, the new tool housing has been reinforced to improve durability during heavy field use.

A factory pre-set bypass cartridge assures a six ton compression every time. The REC-458U accepts either "W" or "O" type dies. The D3 nest die comes standard with the tool. Always consult your connector manufacturer for proper die/connector combinations.

Like the REC-358, the REC-458U will accept the optional 25CAT cutter head attachment. Quick release pins allow the operator to change between compression and cutter head in one minute, with no springs or pins to lose.

To custom order a different tool kit battery and charger combination:

Add the following suffixes to the tool model number:

SM: 2 BP-70EI "Smart" Indicator Batteries

EL: 1 BP-250RI Extended Life Battery

DC: 1 CH-70 DC Charger

 

Catalog#	Size	Output	Description
REC-458U	13"L x 12"H x 3"W	6 Ton	Battery Powered Compression Tool Standard Kit

Gator-Plus™

 

• EK1240 for industry "U" type dies with 1.65"
• EK1240K for Kearney PH2 type dies
• New head designs result in lower weight and improved durability
• Tested to 50,000 crimp cycles
• Two-speed pump to reduce cycle time
• Ram automatically retracts when crimp cycle is complete
• Crimping heads rotate 360°
• Covered head models have two layers of PVC that total approximately 3/16" (4.8 mm) thick; the outer layer is black and the inner layer is red
• Powerful 12 volt 2.0Ah battery provides up to 35 crimps per charge
• Includes one-hour battery charger, steel carrying case, and two batteries
• U.S. Patent 6,206,663

Specifications:

Capacity EK1240

• ASCR terminals 1033 kcmil (MCM)
• ASCR tension fittings 477 kcmil (MCM)
• Crimping Force: 24,000 lbs.
• Length: 15-1/4"
• Weight: 14.9 lbs.

 

Catalog#	Description
EK124012/06437	12-Ton Battery-Powered Crimping Tool, 1.65" (42 mm) Opening, 12 V Charger

Gator-Plus™

 

• Utilizes four indentors to make the crimp
• Two-speed pump advances the ram quickly to start the crimp, reducing crimp completion time; the ram automatically retracts after the crimp is complete
• Lightweight, featuring an angled pistol grip and a 360° rotating head
• Flip-top style uses a pull pin to open head for easy removal from the connector
• Includes two batteries, battery charger, steel carrying case, test gauge and test slugs
• Choice of a 120 volt, 230 volt, or 12 volt one-hour battery charger
• U.S. Patent 6,206,663

Specifications:

Capacity

Connector Type:

• Copper Lugs & Splices: #6 - 500
• Aluminum Lugs & Splices: #6 - 400

Overhead:

• 5/8" Service Ent. Connectors: #8 - 1/0
• .840 Service Ent. Connectors: #4 - 350
• Copper Tension Splice: 6 - 4/0
• One Piece ACSR Tension Splice: #4 - 477
• Length: 14"
• Weight: 11.1 lbs.
• Battery Voltage: 12v
• Battery Charge Time: 1 hour, 120 V Charger

Note: AT tools are UL and cUL classified with #4 - 500 kcmil (MCM) copper color-coded connectors...of the following brands: Anderson, Blackburn, FCI Burndy, ILSCO, Panduit, Penn-Union, & Thomas & Betts.

 

Catalog#	Description
EK06AT12/06070	Quad-Point Battery-Powered Crimping Tool, Open Head Dieless, 12 V Charger

Gator-Plus™

• Utilizes four indentors to make the crimp
• Two-speed pump advances the ram quickly to start the crimp, reducing crimp completion time; the ram automatically retracts after the crimp is complete
• Lightweight, featuring an angled pistol grip and a 360° rotating head
• Flip-top style uses a pull pin to open head for easy removal from the connector
• Includes two batteries, battery charger, steel carrying case, test gauge and test slugs
• Choice of a 120 volt, 230 volt, or 12 volt one-hour battery charger
• U.S. Patent 6,206,663

Specifications:

Capacity

Connector Type:

• Copper Lugs & Splices: #6 - 750
• Aluminum Lugs & Splices: #6 - 750

Overhead:

• 5/8" Service Ent. Connectors: #8 - 1/0
• .840 Service Ent. Connectors: #4 - 350
• Copper Tension Splice: 6 - 4/0
• One Piece ACSR Tension Splice: #4 - 477
• Length: 14-7/8"
• Weight: 10.8 lbs.
• Battery Voltage: 12v
• Battery Charge Time: 1 hour, 120 V Charger

Note: FT tools are UL and cUL classified with #4AWG - 750 kcmil (MCM) copper color-coded connectors and #6AWG - 750 kcmil (MCM) aluminum color-coded connectors of the following brands: Anderson, Blackburn, FCI Burndy, IIsco, Panduit, Penn-Union, and Thomas & Betts.

 

Catalog#	Description
EK06FT12/06073	Quad-Point Battery-Powered Crimping Tool, Flip-Top Head Dieless, 12 V Charger

Gator™

 

• Cuts 500 kcmil (MCM) copper cable in under 8 seconds
• Compact design permits use in tight locations
• Extra heavy blades for clean cuts and long life
• Makes approximately 20 cuts in 750 kcmil (MCM) per battery charge
• Easy to switch between forward and reverse direction
• 12 volt battery recharges in one hour
• Includes battery charger, one battery and molded carrying case
• Choice of a 120 volt or 230 volt battery charger

Specifications:

Cutting Capacity

• 750 kcmil (MCM) (400 mm2) copper cable
• 1000 kcmil (MCM) (500 mm2) aluminum cable
• Length: 14-1/4"
• Weight: 5.8 lbs.
• Battery: 12 Volts NiCd

 

Catalog#	Description
ES750-11/45380	Battery-Powered Cable Cutter, 120 V Charger

Gator-Plus™

 

• The ram automatically retracts after the cut is complete to ready the tool for the next cut
• The two-speed pump advances the ram rapidly to start the cut reducing cycle time
• Cutting head rotates 360° for making cuts in tight locations, and flips open to make mid-span cuts easy
• Includes one-hour battery charger, steel carrying case and two batteries
• Choice of a 120 volt, 230 volt, or 12 volt battery charger

Specifications:

• Length: 15-1/2"
• Height: 12-1/2"
• Weight: 12.8 lbs.
• Battery: 12 volt 2.0 Ah NiCd
• Battery Charge Time: 1 hour

Capacity

• ACSR: 1590 kcmil (MCM), (Falcon 54/19)
• Standard Guy Strand: 5/8" diameter (16 mm diameter)
• EHS Guy Strand: 1/2" diameter (13 mm diameter)
• Ground Rod: 5/8" diameter (16 mm diameter)
• Rebar (schedule 60): 1/2" diameter (13 mm diameter)
• Wire Rope: 5/8" diameter (16 mm diameter)
• Copper and Aluminum Cable: 1500 kcmil (MCM) (800 mm2)
• Soft Steel Bolts: 5/8" diameter (16 mm diameter)

 

Catalog#	Description
ESG45GL12/10413	Battery-Powered ACSR Cable Cutter, 12 V Charger

• Lightweight powder-actuated tools require minimum operator effort
• Installs and removes taps even in confined spaces
• Adaptable for standard hot-stick use
• Conductor applications imprinted on tap packages
• Packages and labels color coded to match taps to tools and cartridges