Section 3600: Tower Assembly

Protoblack™

Protoblack™

 

• Black oxide finish
• Tapered handle for aligning bolt holes
• Spring loaded pellet in male drive plug
• Repair Kit: 5449-14RK

 

Catalog#	Length
5449-14BL	14"

• 10 - 80 ft. lb. thru 140 - 700 ft. lb.
• 2.1 - 11.8 mkg thru 19.4 - 96.8 mkg
• Packaged in blow molded plastic box for protection and easy storage

• Long offset handle provides greater leverage and clearance for knuckles and obstructions
• Hardened tapered handle aligns bolts and rivet holes
• Openings are precision broached for proper fit

Drop-forged from select alloy steel to withstand high-leverage and heavy loads. Extra-heavy-duty head area gives maximum strength and durability. Wrench handle features an extra-deep offset to provide additional hand-clearance without sacrificing tightening power. Continuous taper of handle makes lining-up bolt holes easy, allows use on larger diameter holes than possible with most other wrenches. Available in heavy, regular and utility nut sizes. Catalog number, bolt size and nominal opening size are stamped on every wrench for easy identification. American Bridge Design.

CLIK-STOP®

A drop-forged, heat-treated bull pin which increases efficiency by providing a larger striking surface. Design of the head also reduces chance of pin slipping from the hand when aligning holes. Angled head and smooth blending of radii increase strength and reduce the danger of chipping. Below the head, squared-off shoulders have been forged to provide a surface for applying wrench to loosen wedged bull pins. Long, even taper reduces binding and hang-up. Klein broad-head bull pins offer added resistance to "mushrooming", permitting much longer use than is possible with conventional designs. Black finish. Note: OSHA specifically states that, "impact tools such as drift pins, wedges, and chisels, shall be kept free of mushroomed heads."

Machined from forge-quality alloy steel. Tapers are uniform and blend into body diameter. Tough, drop-forged steel will properly end-pein in use. Heat-treated. Black finish.

This is NOT an occupational protective belt. This rugged 2" wide belt is made of heavy strap leather and equipped with a double-tongue buckle to stand up to years of service. Made of leather.

Wrench holders have tool-slots for two erection wrenches. No. 5460 is slotted to fit on 2" wide belt; No. 5459-T has tunnel loop to fit belts up to 3-1/2" wide or to slide over D-rings, buckles and other accessories. Made of leather.

JM101

 

Dimensions and Specifications:

• Height: 16-1/4"
• Width: 7-1/2"
• Length: 9-3/8"
• Weight: 28 lbs.
• Motor: 0.9 HP 700W (single phase) 120V / 6.0A 450 RPM (no load)
• Arbor bore: 3/4"
• Drill point breakaway: 650 lbs. on 1" plate
• Magnet base dimensions: 3" x 6-1/4"
• Magnet dead lift: 1480 lbs. on 1" plate
• Slugger cutter diameter (maximum): 1-3/8"
• Slugger depth of cut (maximum): 2"

Features:

• A proven performer with positive slug ejection
• Twist drill and tapping options

 

Catalog#	Voltage
19020	120V

Magforce

Slugger advantages:

• Drill holes 3 times faster than twist drills
• Drill unique and curved surfaces
• Allow overlap cuts on existing holes
• Produce reamed quality burr-free holes
• Coolant fed cutting edges
• Produces solid slug
• Reduce machine size and horsepower requirements
• Manufactured with C.N.C. accuracy
• Resharpenable cutting edges
• Eliminate time consuming, costly pilot holes and step drilling

With their unique centerfree design, Slugger cutters cut only the periphery of the hole, ejecting the remaining center as a slug. These cutters produce reamed quality, burr-free holes in one operation, eliminating costly pilot holes and step drilling. Slugger cutters reduce torque and horsepower requirements by having multiple cutting edges and only cutting the periphery of the hole.

Tapmatic® Edge crème lubricates Slugger cutters when drilling in horizontal and inverted positions. The heat that is generated while drilling liquifies the cutting paste, providing coolant and extending cutter life.

Tru-Blue coolant, used with Slugger cutters, is a water-based fluid designed to extend tool life, improve surface finish and reduce heat build-up when drilling.

Carbide Sheet Metal Cutter Features:

• Excellent for hand held or drill press applications
• Heavy-duty carbide tipped cutter outperforms high speed steel or bi-metal cutters in certain applications
• Multiple cutting edge geometry increases productivity
• Great for use in stainless steel, brass or structural steel
• Easy slug ejection
• Low cost with increased hole drilling productivity
• 1/2" shanks with chucking flats for easy hand held operations

Helical Flute Series BR800

BR8001116:

• 11/16" Full Diameter
• 13/32" Approximate Point Diameter
• 7-1/8" Flute Length
• 11" Shank Overall Length
• Taper #3

BR8001316:

• 13/16" Full Diameter
• 35/64" Approximate Point Diameter
• 7-3/8" Flute Length
• 12" Shank Overall Length
• Taper #3

The portable, SH-70M is designed to punch holes through 1/2" mild steel, aluminum and copper. The punched hole size is 1/16" larger than your bolt size. A stripper guide extends on either side of the ram to strip the material after punching. This hand-held unit will operate from any 10,000 psi hydraulic pumping source.

Some uses including punching bus bars, tower iron, railing, I-beams and truck frames.

Custom size punch and dies are available upon request. Oval and square sizes are also available. Consult the factory for order information.

The SH-70M comes complete with four sets of punch and die sizes for 3/8", 1/2", 5/8", and 3/4" bolts, and carrying case.

Specifications:

• Output: 35 ton
• Weight: 28 lbs.
• Capacity: 1/2" mild steel
• Max. hole: 13/16" diameter
• Size: 14"L x 8"H x 3.5"W
• Throat depth: 2.75"

• 9" Diameter
• 6000 RPM
• Powerful 15 AMP 4.0 maximum horsepower - Provides high performance power for grinding, cutting and finishing operations
• Side and main grip angled for optimum comfort
• Lightweight
• Comfortable two finger switch
• 3-Position side handle
• Cast aluminum gear housing with conveniently located spindlelock - Accessory change is fast and easy-single wrench operation
• Spiral bevel gears - For optimum motor torque transfer, improved performance and durability, replaceable armature pinion gear
• Outstanding durability and performance - Epoxy coated field windings and armature gear case is specially sealed, long lasting brushes
• Motor access port for easy debris blow out
• Optimum speed for various accessories - including resin bonded abrasives, wire brushes, resin fiber discs and abrasive flap discs
• Volts AC-DC: 120
• Double Insulated/Grounded: Double insulated
• Switch Lock: Lock-On
• Overall Length: 19.25"

• 7" Diameter
• 6000 RPM
• Powerful 15 AMP 4.0 maximum horsepower - Provides high performance power for grinding, cutting and finishing operations
• Side and main grip angled for optimum comfort
• Lightweight
• Comfortable two finger switch
• 3-Position side handle
• Cast aluminum gear housing with conveniently located spindlelock - Accessory change is fast and easy-single wrench operation
• Spiral bevel gears - For optimum motor torque transfer, improved performance and durability, replaceable armature pinion gear
• Outstanding durability and performance - Epoxy coated field windings and armature gear case is specially sealed, long lasting brushes
• Motor access port for easy debris blow out
• Optimum speed for various accessories - Including resin bonded abrasives, wire brushes, resin fiber discs and abrasive flap discs
• Volts AC-DC: 120
• Double Insulated/Grounded: Double insulated
• Switch Lock: Lock-On
• Overall Length: 19.25"

• Standard service, deep throat style is the most versatile and popular
• Hot forged for strength and hard use
• Forcing screw has heavy rolled Acme thread allowing the screw to turn easily under pressure and is less susceptible to damage
• Forcing screw has a sliding T handle and an impact resistant pad

Plumb®

Plumb®

Plumb®

Double Faced Head with 36" Fiberglass handle.